How To Sew Curtains With Rod Pocket

Curtain rods (we used 2 tension rods since these curtains are nestled into the window frame) step 1: Hang your no sew curtain

How To Make Rod Pocket Curtains Farmhouse kitchen

Fold the fabric 2 inches and press with an iron.

How to sew curtains with rod pocket. 10 minute no sew diy curtain tutorial from unskinny boppy If you want a header above the pocket you will need to add extra inches to top of the rod pocket. Spread the fabric face down and fold its top edge by 3 inches to form a rod pocket that measures 1/2 inch larger than the rod.

Choose your fabric and measure the appropriate length for your window and curtains. A round or flat curtain rod is inserted into the pocket leaving enough of the rod exposed either end to fit into the holders. Thread the rod into the casing.

This creates a pillowcase shape where three sides are sewed and the bottom is open. Draw a line starting from side to side on all across the top of the curtain as well as down from the top seam a distance that is equal to half the rod circumference with adding 1/2 inch. Fold the top over 1 3/4 inches and sew a seam to create the pocket.

Turn down your newly created pocket so the decorative top border is at the top of the panel. Add 5” on to the length you want your curtains to be. You can also add a header for your curtain, which will create an illusion of extra height.

To make the top pocket for the curtain rod, crease the fabric so that the seam is at least double the width of the rod. First, determine which way is up and make sure you do both panels the same. Use hot iron to activate tape;

Sewing a rod pocket valance. Curtains cost a lot of money to buy, so you’d think they’d be hard to sew. Decorative finials create a more finished look unless tops of the curtains are going to be hidden under a valance or pelmet.

Divide the measurement in half and add 1/2 inch for the depth of the rod pocket. Sew on this line to create the rod casing. This is literally 3 yards of fabric hung from a curtain rod.

The fullness of the gathered top created is then adjusted to best present the curtains. These curtains are 62” long when finished, so we cut the fabric to 67”. This tutorial will work well if you have an awkward opening that you'd like blocked off, like the entrance to a laundry room.

Draw a line from side to side across the top of the curtain and down from the top seam a distance equal to half the rod circumference plus1/2 inch. 2 install the curtain rod at its chosen position on the window or wall, according to manufacturer’s instructions. Now hem the top of the curtains and make the rod pocket.

Sew a straight seam across the bottom of the pocket. To create the rod pocket start sewing on this line. So let’s start the process.

It is a little time consuming but all you need is netflix and an iron. Alternatively, measure 3 inches down from the top of the fabric and mark the sewing line, using a row of pins. Then sew close to the edge.

Hem the sides of your curtain panels by folding under and pressing 1″. Then fold it over another 4 inches and iron again. Insert the rod in its brackets, screw on finials and let the curtain fall.

Gather a tension rod, clip rings and some fabric to get a head start on this project. Replace the finial as well as also arrange the gathers evenly all across the rod. Zj starts showing how to sew a rod pocket valance by talking about some of the different types of fabric that can be used for window treatments.

And i have absolutely no problem with that. Window treatments with rod pocket curtains Slip curtain rod, or tension rod, through rod pocket;

Each style has its own advantages and disadvantages. Then fold over and press another 1″ and pin in place. To attach hooks to rod pocket curtains, you must make sure the pin hooks are of the same shape and size.

Sew the top of the panel. By hanging these curtains appropriately, your simple curtain becomes a special one. Then, use a sewing machine or hand sew the seam into place before removing the pins.

She includes two options to make a rod pocket or tabs for the top. I like to make this top seam about 1 1/2″ from the edge of the fabric. Gemia at phat quarters has a tutorial showing how, including how to figure out how big to cut your fabric to make curtains to fit your window.

If any pin is too open press them to make a bit tighter. To create the pocket you would add 3 1/4 inches to the top of the curtain once you’ve got the measurement from the bottom of the rod pocket to the floor. Some fabrics are the same both directions, some aren’t.

She then talks about how the fabric needs to be hemmed. To complete your rod pocket curtains, this is what you should do. Form the pocket, sew along the bottom crease about half an inch away from the edge.

How to make your own no sew curtain Remove the rod from its brackets and slide the panel on, bunching evenly to one side. These are not designer curtains or black out curtains.

Suppose the diameter of the rod is 2 inches. Create rod pocket fold the top fabric over 3 1/4 inches, pin, and sew along the fabric's edge so that a pocket forms between the top of the curtain and the stitch. Use your measurement for the length to figure out how long your finished curtains should be.

Fold down your new folded edge so it lines up with the seam beneath the decorative border. While a standard double fold hem of nearly any size can work on a rod pocket valance, there are generally wider recommended widths of hems for window treatments. The top hem forms the rod pocket which should be at least twice the diameter of the curtain rod.

With the wrong side of the fabric facing you, fold the top over twice, pin it in place and sew. Making your own curtains is not difficult especially if you go the no sew option. Pin the seam in place and iron the crease to ensure that it stays in place.

See more ideas about curtains, tension rod curtains, tension rod. Pin the pocket in place and press it with the iron.

Looking for more beautiful drapery fabric? Click here to